Uninterruptible Power Supply SANUPS E11A102A Instruction Manual M0007084E
− 7 − (5) Insulation testing Before testing indoor wiring insulation, shut down the UPS and disconnect the input and output cables. Conducting an in
− 8 − 4. Overview The SANUPS E11A is a stationary-type uninterruptible power supply designed to provide high-quality, stable AC power to critical e
− 9 − EXT.BATT17.32440MAIN SW863.39 5. External Dimensions and Part Names 5.1 Front and Back Panels Depth: 408 mm (1
− 10 − 5.2 Control Panel and Indicators Functions No. Label Status display Lit Not lit Slow blink Fast blink LED0 INPUT Input pow
− 11 − EXT.BATTMAIN SW 5.3 External Interfaces UPS back panel No. Name Function ① PC I/F (PC interface) (RS-232C) Allows you to contro
− 12 − 6. Installation CAUTION ! ・ When installing the UPS, carefully follow the instructions in this Instruction Manual. ・ Install the UPS on a
− 13 − 6.4 Preparation Before Installation CAUTION ! ・ Wear insulated gloves and take other precautions when connecting the batteries. Otherwise
− 14 − 6.5 Attaching the Stand CAUTION ! ・ Unless the UPS is secured solidly in place, it can shift or fall during seismic events (earthquakes) o
− 15 − 6.6 Mounting a Rack Mount Type UPS CAUTION ! ・ Be careful to avoid straining your lower back when moving and installing the UPS. ・ The UP
− 16 − BATTEXT.MAIN SWINPUT plug (seen from prong side) Note When the AC input power is single-wiregrounded, always connect the groundphase to the S
− 17 − BATTEXT.MAIN SW ③ Connect the input power plugs of the load devices to the output terminals. Output terminal capacity Note 125V 1
− 18 − 8. Preparations Before Operation Check the following items before starting operation: ① Visually inspect the UPS to verify that there is n
− 19 − EXT.BATTMAIN SW 9. Operating Procedures 9.1 UPS Startup (Normal Operation) Check that the INPUT indicator has chang
− 20 − 9.2 UPS Startup (Battery Power) During a power outage, low voltage, or other trouble with the AC input power to the UPS, you can supply powe
− 21 − 9.3 Outage Simulation Test You should perform a test of whether the UPS operates properly during a power outage. Proper operation is as de
− 22 − 9.4 UPS Shutdown (Daily) Note Do not touch MAIN SW when you perform a daily shutdown. Leave it set to the “ON” position. *
− 23 − 10. User Settings 10.1 Setup Menu Item List You can configure the UPS by setting the menu items in the following list. Configure it accordin
− 24 − Two beeps sound from the buzzer. The setting is saved and the UPS returns to normal operation. 10.2 Setup Menu Operations Set all menu items
− 25 − 11. Maintenance and Inspection 11.1 Daily Inspection Check the control panel LED indicators to confirm that no error is indicated. No other
− 26 − 11.4 Battery Maintenance CAUTION ! ・ Internal maintenance and inspection should be performed only by technically qualified personnel. Elec
Introduction Thank you for choosing the SANUPS (E11A102A). SAVE THESE INSTRUCTIONS This manual contains important instructions for E11A102U001 that s
− 27 − 11.5 Battery Test You can perform automatic and manual tests of the built-in and externally connected batteries. You can do this without sto
− 28 − 11.6 Battery Exchange You can exchange the batteries without stopping the load devices. However, this should be done as quickly as possible,
− 29 − ⑦ Attach the battery cover. ⑧ Attach the front panel. ⑨ Rest the remaining battery service life with item ⑯ “Reset r
− 30 − 11.7 Bypass Fuse Exchange CAUTION ! Always power the UPS off before exchanging the fuse. Failure to do so can cause electric shock. Be car
− 31 − 12. Troubleshooting If a problem occurs, check the condition of the equipment and perform countermeasures as listed in the table below. CA
− 32 − Condition Countermeasure No recovery from utility power source failure. Utility power source failure occurs frequently. ・ Check whether MA
− 33 − 13. Alarm Sounds The alarm buzzer emits sound patterns to alert you to failures and error conditions in the UPS. Check the sound pattern and
− 34 − 14. Maintenance Bypass Power Supply (Option) You can combine this UPS with an optional Maintenance Bypass Unit. In the event of a failure in
− 35 − 15. Functional Description 15.1 Basic Operation (1) Normal Operation In normal operation, the UPS switches automatically* between the thre
− 36 − (c) Economy mode The UPS switches to Economy mode when the input power voltage is within a certain range and the output power factor is above
− 1 − 1. Safety Precautions PRECAUTIONS (IMPORTANT SAFETY INSTRUCTIONS) Before installing, operating, performing maintenance or inspecting the UPS,
− 37 − 15.2 Protective Functions (1) Overload Protection If the UPS output is overloaded by exceeding the current capacity of the inverter, such as
− 38 − 15.3 Protective Function Table The following table shows functions and operations which activate to protect the UPS. The ○ mark indicates li
− 39 − 15.4 Specifications Item Standard or Performance Notes Output capacity 1kVA/0.7kW Cooling system Forced air cooling Phases Single
− 40 − 16. Warranty Warranty for Use Overseas (North America) 3 Years 1. This product is warranted against electrical failure due defects in m
− 41 − Appendix Usage notes for SANUPS SOFTWARE STANDALONE When using supplied “SANUPS SOFTWARE STANDALONE”, please note the following instructions
− 42 − LED blinking for setting up menu For the following two Menu Item, • “Restart time (battery charge rate)” in the E11A Instruction Manual §1
− 2 − 1. Installation Precautions CAUTION • The UPS should be installed only by technically qualified personnel. Improper installation can result in
− 3 − 3. Operating Precautions DANGER • Immediately shut the UPS off if it malfunctions, or if an unusual odor or noise is observed. Failure to do so
− 4 − 4. Radio Frequency Interference CAUTION • This equipment has been tested and found to comply with the limits for a Class A digital device, purs
− 5 − 7. Battery Handling Precautions CAUTION • Risk of explosion if battery is replaced by an incorrect type • Dispose of used batteries accordin
− 6 − 2. For Proper Operation 2.1 Input Power Requirements (1) Make certain that the AC input voltage and frequency correspond to the specified eq
Comments to this Manuals