Sanyo PLC-WXU30 Owner's Manual Page 67
- Page / 82
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
67
Problem: – Solutions
No power – Plug the power cord of the projector into the AC outlet.
– See if the POWER indicator lights red.
– Wait until the POWER indicator stops blinking to turn on the projector
again. The projector can be turned on after the POWER indicator
turns red. See page 22.
– Check the WARNING indicator. If the WARNING indicator lights red,
projector cannot be turned on. See page 62.
– Check the projection lamp. See page 65.
– Unlock the Key lock function for the projector. See page 54.
The initial display is not shown. – Make sure "User" or "Countdown off" are not chosen at display
function.(see page 48)
The initial display is not same – Make sure "User" or "Countdown off" are not chosen at Logo (select)
as the default set. function.(see page 48)
Input signal switches automatically. – Make sure Input search function is adjusted properly. See page 51.
(or does not switch automatically)
When the projector is on and you – That is the Filter warning icon. Refer to page 57.
press the input button, an icon
other than the Lamp mode icon
appears.
An icon other than Input mode or – That is the Lamp replacement icon or the Filter warning icon. See
Lamp mode icon appears. page 56 or 57.
Image is out of focus. – Adjust focus of the projector. See page 26.
– Provide proper distance between the projector and the projection
screen. See page 17.
– Check the projection lens to see if it needs cleaning. See page 64.
– Moving the projector from a cool to warm place may result in
moisture condensation on the projection lens. In such cases, leave
the projector off and wait until condensation evaporates.
Image is Left/Right reversed. – Check the Ceiling/Rear function. See page 51.
Image is Top/Bottom reversed. – Check the Top/Bottom function. See page 51.
Picture is not bright enough. – Check if the 'Contrast" or "Brightness" are adjusted properly.(see
page 37,44)
– Check if "Image mode" is selected properly.(see page 36,43)
– Check the lamp control function.(see page 28)
– Check the LAMP REPLACE indicator. If it lights, the end of lamp life
is approaching. Replace the lamp with a new one promptly.(see page
65)
Appendix
Troubleshooting
Before calling your dealer or service center for assistance, check the items below once again.
– Make sure you have properly connected the projector to peripheral equipment as described on pages 19-21.
– Make sure all equipment is connected to AC outlet and the power is turned on.
– When the projector does not project an image from the connected computer, restart the computer.
- PLC-WXU30 1
- Features and Design 3
- Table of Contents 4
- 0.7’(20 cm) 5
- 1.5’(50 cm) 5
- Safety Instructions 6
- Moving the Projector 7
- Air Circulation 7
- Compliance 9
- Corporation 10
- Rear Terminal 11
- Top Control 12
- Remote Control 13
- Part Names and Functions 13
- Pointer Function 14
- Laser Pointer Function 14
- Wireless Mouse Operation 15
- Remote Control Code 15
- Adjustable Feet 16
- Installation 17
- Connecting the AC Power Cord 18
- Connecting to a Computer 19
- Connecting to Video Equipment 20
- Basic Operation 22
- Turning Off the Projector 23
- Menu Bar 25
- For computer source 25
- For video source 25
- Zoom and Focus Adjustment 26
- Keystone Correction 26
- Auto Setup Function 26
- Sound Adjustment 27
- Remote Control Operation 28
- • • • • • 29
- Computer Input 30
- Computer System Selection 32
- Auto PC Adjustment 33
- Manual PC Adjustment 34
- Image Mode Selection 36
- Image Adjustment 37
- Screen Size Adjustment 38
- Video Input 40
- Video System Selection 42
- Setting Menu (Language) 47
- Auto setup 47
- Keystone 48
- Logo select 49
- Enter a Logo PIN code 50
- Change the Logo PIN code 50
- Ceiling 51
- Power management 52
- Remote control 53
- Lamp control 53
- Key lock 54
- PIN code lock 54
- Enter a PIN code 55
- Change the PIN code 55
- Fan Control Setting 56
- Factory default 57
- Filter counter 57
- Set the alarm 58
- Release the alarm setting 58
- Antitheft Alarm Function 59
- Maintenance and Cleaning 62
- Resetting the Filter Counter 63
- Cleaning the Filter 63
- Lamp Replacement 65
- Resetting the Lamp Counter 66
- Appendix 67
- Menu Tree 71
- Small/Medium/Large 72
- Low/Medium/High 72
- 10 seconds/60 72
- Projector Condition 73
- Technical Specifications 76
- Optional Parts 77
- PJ Link Notice 78
- 8 7 6 5 4 3 2 1 79
- Lamp Replacement Label 80
- Unit: inch(mm) 81
- Screw Holes for Ceiling Mount 81
- Screw: M4 81
- Depth: 0.472(12.0) 81
- SANYO Electric Co., Ltd 82
Related products and manuals for Data projectors Sanyo PLC-WXU30
Data projectors Sanyo PDG-DWT50L User Manual
(135 pages)
(135 pages)
Data projectors Sanyo PDG-DXT10L User Manual
(135 pages)
(135 pages)
Data projectors Sanyo PDG-DXT10L User Manual
(135 pages)
(135 pages)
© 2020, manymanuals.com. All rights reserved. | 0.326 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals