Sanyo 52SR1 Instruction Manual download pdf (Page 10)

This LCD monitor allows you to set up the following:

SETTING PROCEDURE

1.Press and hold the GREEN button on the remote control for 5

seconds. (Installation Mode will appear)

Use the 5 or 6 button to highlight each option, use the

1 or

button to adjust each option.

Press the MENU button to exit

the mode.

 On Program

Select ON program using the

5 or 6 button, select the start up

position using the

1 or 2 buttons.

(Off/ AV1/ RGB/ AV2/ AV3/ PC/ DVI or Network)

 Max Volume

Select Max volume using the

5 or 6 button, use the

1 or

2 buttons to set the maximum volume required.

 Winter mode

This Function can be activated when the LCD monitor is used during

cold temperature conditions, approximately 38˚F/ 4˚C or below to

maintain picture performance.

Using the

5 or 6

button select winter mode, once highlighted

you can select ON or OFF by pressing the 1 or 2 button.

IMPORTANT: The AC cord should not be disconnected during the

operation of Winter mode function.

When in winter mode, power consumption is higher than normal

standby consumption. This is entirely due to the operation of heating

circuitry. We strongly recommend to turn off Winter mode when the

ambient temperature is above 38˚F/ 4˚C.

 RC inhibition

You can prevent unwanted remote control operation by selecting RC

Inhibition.

Select using the

5 or 6

button. Press the 1 or 2 button

to select On or Off.

To re-instate RC operation press and hold the green button on the

remote control and select RC inhibition OFF.

 Child Lock

You can prevent unwanted operation of the LCD monitor via the

buttons on the rear of the monitor.

Select using the

5 or 6

button. Press the 1 button to select

On or OFF. The ‘Child Lock’ OSD will appear if buttons are pressed

when child lock is On.

 Standby operates normally when childlock is set “On”.

 Address

Set the address for the LCD monitor (0 - 999).

 Baud rate

Select Baud rate using the

5 or 6

button. To set transmission

speed RS232 or LD-NET communication for 19200 or 9600 Baud

rate by pressing the 1 or 2 button.

 Panel Protect

Select Panel Protect using the

5 or 6

button, once highlighted

you can select ON or OFF by pressing the 1 or 2 button.

 AV Auto shut off

Select AV Auto Shut Off using the

5 or 6

button, once high-

lighted you can select On or Off by pressing the 1 or 2

button.

 LED Light setting

Select LED Light setting using the

5 or 6

button, once high-

lighted you can select On or Off by pressing the 1 or 2

button.

 DCR

Select DCR using the

5 or 6

button, once highlighted you can

select On or Off by pressing the 1 or 2 button.

 Network Initial

This function automatically installs the IP Address, Subnet, Gateway

and DNS information.

 Temperature Error

This function can record times for abnormal temperture.

 IP Address / Subnet / Gateway / DNS

These 4 items display the LD-Net information. If LD-NET is NOT

connected, all the items would be displayed as “000000000000”.

 Disconnecting the mains supply before exiting Installation Mode

will cancel the following features On program, RC inhibition, Address

and Baud Rate.

INST

ALLA

TION MODE

Installation Mode

Temperature Error

VER -.--

Network Initial

>>>

Installation Mode

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 16 17 18

Comments to this Manuals

No comments

Sanyo 52SR1 Instruction Manual Page 10

Comments to this Manuals

Related products and manuals for Public displays Sanyo 52SR1