Sanyo CE-42LH2WP Instruction Manual download pdf (Page 31)

English

Step: 1 Mains Connection

N&RQQHFWWKHGLVSOD\XQLWWR9*$%1&DQG6FDUWFRQ-

nector as required.

1. Connect the in-line power connector to the Mains Inlet as shown

above.

Connect the power cord of the LCD monitor to a suitable wall

outlet.



As this product does not have a mains On/Off switch, please

ensure your mains plug is easily accessible.



The LCD monitor is prepared for a mains voltage AC100 ~ 240V,

+]+]7RFRPSOHWHO\VZLWFKRIIWKHPDLQVRUZKHQWKH

GLVSOD\XQLWLVQRWWREHXVHGIRUDQH[WHQGHGSHULRGRIWLPHLWLV

advisable to disconnect the power cord from the power outlet.

 Please use the correct mains lead supplied with the set for your

area.

3. Warning: To prevent injury, the unit must be securely attached to

the wall in accordance with the installation instructions.

WARNING! High voltages are used in the

RSHUDWLRQRIWKLVVHW5HIHUVHUYLFHWRTXDOLÀHG

service personnel.

Step: 2 Connections

NINPUT selection

To switch either AV1, RGB, AV2, AV3, PC, DVI or Network by pressing

the INPUT button on your remote control repeatedly.

1. AV1

SCART connection/CVBS/RGB/S-VIDEO.

2. RGB

TTL input (5V RGB signals) into SCART terminal.

<3E3U5*%+9FRQQHFWLRQ$9

Choose Y, Pb, Pr or RGB H/V connection by selecting AV2 Setting

in Set up menu (refer to the INSTRUCTION MANUAL on page 10).

You can connect your DVD player to the Y, Pb, Pr terminals instead

RIXVLQJDVFDUWOHDG7KLVFDQVXSSRUWKLJKGHÀQLWLRQLQDQDORJXH

component form. RGB H/V can be used as a PC input via the BNC

terminals. Both options support a large range of resolutions (refer

to the INSTRUCTION MANUAL on page 17). AV2-OUT can be used

to output the incoming AV2 signal to the other monitor.

4. AV3

Composite (CVBS) signal input.

AV3-OUT can be used to output the incoming AV3 signal to the

other monitor.

5. DVI-D (Digital Video Interface)

DVI-D supports a large range of resolutions as shown in the IN-

STRUCTION MANUAL on page 17.

6. PC connection

PC input (PC-IN D-SUB). This input supports a large range of reso-

lutions as shown in the INSTRUCTION MANUAL page 17. Audio

can be connected via the 3.5mm PC-AUDIO IN.

7. External Speaker

Output the audio signal from AV1, AV2, AV3, PC and DVI.

The speaker impedance is 8 ohms.

8. AV2 / DVI AUDIO IN

Connect the audio output (stereo) from a computer or video equip-

ment connected AV2 or DVI.

9. Monitor Audio OUT

7KLVWHUPLQDOVRXWSXWÀ[HGOHYHOIURP$8',2,1

10. RS232C IN/OUT

When the monitor is controlled by a computer, connect to this jack

with serial control cable.

You can connect to another monitor with RS232C OUT.

:KHQ\RXFRQQHFW3&ZLWK56&VHOHFW´21µDW1HWZRUN

standby in Installation mode.

,ILWLVVHOHFWHG´2))µ56&WHUPLQDOVGRQRWIXQFWLRQDO$OVR

VHOHFWSXVKEXWWRQWR´6(5,$/32$57µ

INSTALLATION

AC Mains Outlet

7KLVÀJXUHLVLQFKPRGHO

LD-Net

GB GB

1 2 ... 26 27 28 29 30 31 32 33

Comments to this Manuals

No comments

Sanyo CE-42LH2WP Instruction Manual Page 31

Comments to this Manuals

Related products and manuals for Public displays Sanyo CE-42LH2WP