Sanyo DVDSL40 Datasheet download pdf (Page 19)

CLASS 1 LASER PRODUCT

LUOKAN 1 LASERLAITE

KLASS 1 LASERAPPARAT

PRECAUTIONS

The unit is not disconnected from the mains unless it is unplugged from the AC outlet.

IMPORTANT

If the plug supplied with this equipment is not suitable for the socket

outlets in your home it should be cut off and replaced with the cor-

rect type.

Disposal of Plug

If the non rewireable plug is to be cut off, the removed plug should

be disposed of carefully as there is a shock hazard should the plug

be inserted into a live socket.

Replacing Fuse

The detachable fuse cover must be replaced after changing the

fuse. Only a 3A fuse should be used and should comply with BS

1362 and should carry the ASTA mark .

The wires in the mains lead are coloured in accordance with the

following code.

Blue Neutral

Brown Live

The wires in the mains lead must be connected to the terminals in

the plug as follows:

Wire colour Plug terminal marking

Blue N or Black or Blue

Brown L or Red or Brown

Do not connect either wire to the earth terminal.

If the mains plug contains a fuse this should be 3A, if a plug without

a fuse is used the distribution board fuse should not be greater

than 5A.

CAUTION

THIS PRODUCT CONTAINS A LOW POWER LASER DEVICE,

TO ENSURE CONTINUED SAFETY DO NOT REMOVE ANY

COVERS OR ATTEMPT TO GAIN ACCESS TO THE INSIDE OF

THE PRODUCT.

REFER ALL SERVICING TO QUALIFIED PERSONNEL.

CLASS 1 LASER PRODUCT

LUOKAN 1 LASERLAITE

KLASS 1 LASERAPPARAT

- The apparatus shall not be exposed to dripping or splashing.

- No objects filled with liquids, such as vases, shall be placed on

the apparatus.

- Do not use where there are extremes of temperature (below 5 °C

or exceeding 35 °C) or where direct sunlight may strike it.

- Because of the DVD player’s extremely low noise and wide dy-

namic range, there is a tendency to set the volume on the ampli-

fier higher unnecessary high. Doing so may produce an exces-

sively large output from the amplifier which could damage to your

speakers.

- Sudden changes in the ambient temperature may cause con-

densation to form on the optical lens inside the unit. If this

happens, take out the disc, leave the unit for about 1 hour, and

then proceed to operate.

- When carrying the unit, be sure to remove a disc which may be

inside and turn the power off. Wait at least 10 seconds, then

unplug the mains lead from the AC outlet. Carrying the unit with

a disc inside may damage the disc and/or the unit.

- Do not install this equipment in a confined space, such as a book

case or built in cabinet.

- The unit is not completely disconnected from the mains when

the z/ON button is set to the z position.

- The unit is automatically set to the screen saver mode after ap-

proximately 15 minutes have elapsed under the stop or pause

mode.

- The unit is automatically set to the standby mode after approxi-

mately 30 minutes have elapsed under the complete stop or pause

mode.

Important information:

To connect this unit to a TV, TV must have a set of Audio/Video com-

posite input sockets or an EURO-AV/SCART socket at least. You

cannot use an RF input socket or aerial terminal to connect this unit.

This product incorporates copyright protection technology that is pro-

tected by method claims of certain U. S. patents and other intellec-

tual property rights owned by Macrovision Corporation and other rights

owners. Use of this copyright protection technology must be autho-

rized by Macrovision Corporation, and is intended for home and other

limited viewing uses only unless otherwise authorized by Macrovision

Corporation. Reverse engineering or disassembly is prohibited.

POSSIBLE CAUSE

No disc is loaded.

An unplayable disc is loaded.

The TV is not set to receive signal from the

player.

No video connection.

No audio connection.

An unplayable disc is loaded.

The selected function does not operate on the

disc now.

No disc is loaded.

An unplayable disc is loaded.

The disc is loaded with the label side down.

The disc is dirty.

“PARENTAL” is set.

The unit must be reset.

An unplayable disc is loaded.

“PARENTAL” is set.

The disc may not have the correct file or data.

The batteries in the remote control are weak,

or installed incorrectly.

The remote control is not aimed at the remote

sensor window.

SYMPTOM

No picture.

No sound.

The playback picture is poor.

“ ” appears on the TV screen.

No start play.

The operation or display is not normal.

“NO PLAY” appears on the TV screen.

The remote control does not work properly.

CORRECTIVE ACTION

Load a disc.

Load a playable disc. (Check the disc logo,

type, color system and regional code.)

Select the correct input function on the TV.

Connect the video lead to the appropriate

socket.

Connect the audio leads to the appropriate

sockets.

Load a playable disc. (Check the disc logo,

type, colour system and regional code.

The feature or action cannot be completed at

this time because:

- The feature is not available at the

moment.

- The DVD software restricts it.

- The DVD software does not support the

feature (e.g., angles).

Load a disc.

Load a playable disc. (Check the disc logo,

type, colour system and regional code.)

Load the disc on the disc tray correctly.

Clean the disc or replace it.

Cancel the parental lock function or change

the rating level. Reset it after play.

1. Disconnect the mains lead.

2. Reconnect the mains lead.

3. Resume operation.

Load a playable disc. (Check the disc logo,

type, color system and region number. See

page 6.)

Cancel the parental lock function or change

the rating level. Reset it after play. (See page

17.)

Load a playable disc. window,

Check the battery polarity (+ or –).

Replace the batteries.

Aim the remote control at the remote sensor.

TROUBLESHOTTING GUIDE

If you have followed the instructions and are having difficulty operate the unit, locate the SYMPTOM in the left column below. Check the

corresponding POSSIBLE CAUSE and CORRECTIVE ACTION columns to locate and remedy the problem.

CLEANING THE UNIT

Clean the outside of the unit with a clean soft cloth moistened with lukewarm water. Do not use benzene or alcohol since they will mar the finish

of the surfaces.

DVD-SL40/88/255/UK-book 4/27/04, 3:08 PM2

1 2 ... 14 15 16 17 18 19 20

Comments to this Manuals

No comments

Sanyo DVDSL40 Datasheet Page 19

Comments to this Manuals