Sanyo 32LM5R Instruction Manual download pdf (Page 2)

SAFETY

PRECAUTIONS

Do not allow anything to rest on the power

cord. Do not locate this LCD monitor where

the cord will be damaged by people walking

on it.

Do not overload wall outlets and extension

cords as this can result in fire or electric

shock.

A suitable socket outlet must be provided

near to the monitor and shall be easily accessible.

Do not place this LCD monitor near any heat sources such as

radiators, heaters, stoves and other heat-generating products

(including amplifiers).

Do not place your LCD monitor on an unstable stand, shelf or

table. Serious injury to an individual, and damage to the LCD

monitor may result if it should fall. Your sales person can

recommend approved wall mounting kit. A special wall mounting

kit is available for this model.

This LCD monitor should be operated only from the type of power

source indicated on the monitor or as indicated in the Operating

Instructions. If you are not sure of the type of power supply, con-

sult your sales person or your local power company

For added protection it is strongly recommended that this LCD

monitor is supplied via an approved earth fault protection device.

WARNING: To prevent injury the LCD monitor must be securely

attached to the wall in accordance with the manufacturers installa-

tion instructions.

IMPORTANT:

This product must be earthed

This unit is not disconnected from the mains unless the mains lead is

unplugged. The installer must make sure that the mains plug is easily

accessible.

Do not use immediately after moving the LCD monitor from a low

temperature to a high temperature environment, as this causes

condensation, which may result in fire, electric shock, or other

hazards. Before cleaning, unplug the monitor from the wall

socket.

Do not mount near an open flame source. Open flames must

never be used near this LCD monitor.

This LCD monitor should not be built in or enclosed in any way,

heat build up will reduce the life of the monitor.

This LCD monitor should have a minimum distance of 5cm away

from the wall and the monitor should have 10cm distance around

the top and sides.

Always mount using recommended and substantial fixtures and

fittings.

The rear finned section around the cabinet functions as a heat

sink, removing heat away from the monitor. The external surface

of the cabinet (finned area) must not be covered or the airflow

restricted in anyway by enclosing the LCD monitor.

Do not apply liquid cleaners or aerosol cleaners directly onto the

LCD monitor. Use a damp cloth for cleaning.

Installation and Use

CAUTION: Please read and retain for your safety. This unit has been engineered and manufactured to assure your personal safety, but

improper use can result in potential electric shock or fire hazards. In order not to defeat the safeguards incorporated in this monitor observe the

following basic rules for its installation, use and servicing.

Important: (UK only)

THIS PRODUCT MUST BE EARTHED

This equipment is fitted with an approved mains lead and an

approved non rewireable UK mains plug. To change a fuse in this

type of plug proceed as follows:

1. Remove the fuse cover and fuse.

2. Fit a new fuse which should be a BS1362 13 Amp A.S.T.A. or

BSI approved type.

3. Ensure that the fuse cover is correctly refitted.

If the fuse cover is lost or damaged the plug must NOT be used

but replaced with a serviceable plug.

If the fitted plug is not suitable for your socket outlets, it should be

cut off and an appropriate plug fitted in its place. If the mains plug

contains a fuse, this should have a rating of 13 Amp, ensure the

fuse cover is correctly fitted. If a plug without a fuse is used, the

fuse at the distribution board should not be greater than 13 Amp.

Note: The severed plug must be destroyed to avoid a possible

shock hazard should it be inserted into a 13 Amp socket elsewhere.

The wires in this mains lead are coloured in accordance with the

following code:

Blue -------> Neutral

Brown ----> Live

Green and Yellow ----> Earth

1. The Blue wire must be connected to the terminal whichis

marked with the letter “N” or coloured BLACK.

2. The Brown wire must be connected to the terminal with the

letter “L” or coloured RED.

3. The Green and Yellow wire must be connected to the terminal

which is marked with the letter “E” or coloured GREEN or

GREEN and YELLOW.

Before replacing the plug cover, make certain that the cord grip is

clamped over the sheath of the lead - not simply over the wires.

Do not attempt to bypass the safety purpose of the grounding

type plug.

THIS UNIT IS NOT DISCONNECTED FROM THE MAINS UNLESS

THE MAINS LEAD IS UNPLUGGED.

THE INSTALLER MUST MAKE SURE THE MAINS LEAD IS

EASILY ACCESSIBLE.

10cm

5cm

1 2 3 4 5 6 7 ... 67 68

Comments to this Manuals

No comments

Sanyo 32LM5R Instruction Manual Page 2

Comments to this Manuals

Related products and manuals for LED displays Sanyo 32LM5R