Sanyo LNS-W32 User Manual download pdf

Following checks and confirmations should be taken for safety.

Check the following things by the time of the cabinet assembly after the lens

replacement.

1. Check the lens is securely fixed.

2. Check no parts is missing, or no mounting part is loose.

LCD PROJECTOR LENS

MODEL LNS-W32

LENS REPLACEMENT PROCEDURE

NOTES ON LENS REPLACEMENT

The ZOOM, FOCUS and LENS SHIFT adjustment on the Top Control or the

Remote Control cannot be operated with this Lens.

Lens replacement should be performed by the qualified service personnel.

It should be followed by this procedure precisely.

Before attempt to replace the lens, confirm the model number (both the LCD

projector and the lens) and use the proper lens.

The lens cover is on the lens for protection. Be sure to remove the lens cover

before installation.

When installing or removing the lens, be careful not to stain, scratch or

damage the lens.

Following parts are contained in the packing.

1AA6P1P3217A- (ICZAA-A)

PARTS LIST

● LENS

● LIGHT-BLOCK SHEET BASE

● DRIVER (3 mm, Green)

● DRIVER (4 mm, Yellow)

● LIGHT-BLOCK SHEET

● SCREW

1 piece

1 piece (Part No. 610 310 8001)

1 piece (Part No. 610 287 7328)

1 piece (Part No. 610 275 6029)

1 piece Type PC1 (Part No. 610 310 7967)

1 piece Type PD1 (Part No. 610 294 3047)

2 pieces (Spare parts)

Some parts are not used for installation or replacement. Keep these parts and

drivers included in the lens for later use.

NOTE; Lens installation is different in cabinet design and lens attachment method

(Type A, B and C). Before installation the lens, check cabinet design and

proper installation should be made.

1 2 3 4 5 6 7 8 9 10

Summary of Contents

Page 1 - LENS REPLACEMENT PROCEDURE

Following checks and confirmations should be taken for safety.Check the following things by the time of the cabinet assembly after the lensreplacement

Page 2

- 10 -FOCUS ADJUSTMENTSet up the projector and project image on the screen.1. Loosen the Focus Lock Screw on the lens.2. Rotate the lens to obtain pro

Page 3

Fig-1Fig-2Fig-3Fig-4SCREW "A"Remove 2 screws-A.Press the button (or remove 2 screws-B) onthe lower of the front panel and remove thefront pa

Page 4

3REMOVE THE LENS (See Figure-5 and 6)Disconnect the Lens Shift connector "K16L" fromthe circuit board on cabinet left side. Disconnect the Z

Page 5

-4-Fig-6Fig-7DRIVERIN THE LENSLENS MOUNTINGBRACKET4MOUNT THE LENS (See Figure-5 and 6)5MOUNT THE LIGHT-BLOCK SHEET ANDFRONT PANEL (See Figure-7)Remove

Page 6 - LENS LOCK LATCHES

Turn the lens cover to counter-clockwise andpull it toward front and remove the LensCover.Remove 2 Screws-A.Remove the front cabinetREMOVE THE LENS CO

Page 7

4MOUNT THE LENS (See Figure-5)Remove protective caps (front and back) on thelens.Mount the lens on lens mounting bracket withUpper 2 screws.Use the dr

Page 8 - Lock Lever

FOCUS ADJUSTMENTSet up the projector and project image on the screen.1. Loosen the Focus Lock Screw on the lens.2. Rotate the lens to obtain proper fo

Page 9 - Correcting the focus

- 8 -Turn the lens cover to counter-clockwise and pull ittoward front and remove the Lens Cover.Remove 2 Screws-A.Remove the front cabinetREMOVE THE L

Page 10 - FOCUS ADJUSTMENT

- 9 -LENSATTACHMENTPart No. (610 275 6029)4MOUNT THE LENSRemove protective caps (front and back) on the optional lens.Mount the lens on the lens attac