Sanyo VCC-5974 User Manual

INSTRUCTION MANUALCOLOR CCD CameraVCC-5974About this manual• Before installing and using the camera, please read this manual carefully. Be sure tokee

MOUNTING THE LENSInstallation of a VIDEO type auto-iris lens(sold separately)A 1/2 or 2/3 inch C mount type lens with EE amplifier circuitthat uses th

MOUNTING THE LENSCompatible auto-iris lenses1/3 inch Sanyo DC type lens 1/2 or 2/3 inch VIDEO type lensVCL-CS8LY: Standard angle, f= 8 mm Standard ang

SETTINGSThe illustration shows the factory default settings for the switches in the camera setup section.Depending on the camera installation location

SETTINGSAutomatic Gain Control (AGC) settingThe automatic gain control can be turned ON or OFF using theAGC ON/OFF switch (6) in the camera setup sect

ONOFFAIEI WINDOW WEIGHTING W0 1 W1 1 W2 3 W3 3 W4(FIX) 15 PRESET OFF MENU EN

USING THE ON-SCREEN MENUS MENU FOR ADJUSTMENT SYNC INT IRIS AI BLC ON WHITE BALANCE ATW AGC ON SHUTTE

ADJUSTMENTSTo enter settings or adjustments for the camera it must beconnected to a monitor. The settings and adjustments are madeby ways of on-screen

ADJUSTMENTS1. SYNC1-1. V sync phase adjustmentWhen using a camera switcher to connect 2 cameras or more toone monitor, there may be a vertical roll of

1-2. VBS phase adjustment1 Connect a VBS signal source to the VBS IN connector on thecamera.The on-screen setting will automatically switch to VBS. Pr

ADJUSTMENTS2. IRIS2-1. Auto-iris level adjustment1 Set the IRIS switch (10) to AI.The on-screen setting will automatically switch to AI. Press theCURS

SANYO INDUSTRIAL VIDEOCOLOR VIDEO CAMERA LIMITED WARRANTYOBLIGATIONSIn order to obtain warranty service, the product must be delivered to and picked u

ADJUSTMENT FOR BLC BLC MODE PRESET 1 ADJUSTMENT FOR BLC (SIZE) ADJUSTMENT FOR BLC (POSITION) WINDOW WEIGHTING W0 1

ADJUSTMENTS5 Press the CURSOR (j or l) button to select the desiredwindow (get its value flashing), then press the CURSOR (dor c) button to set the de

3-2. BLC level adjustment for the PRESET 1setting1 Set the BLC switch (9) to ON. The on-screen setting for BLCwill automatically switch to ON. Press t

ADJUSTMENTS4. WHITE BALANCE4-1. PRESET MODE 2 (indoors, fluorescentlighting) setting adjustment1 Set the WB switches to the PRESET mode (switch 7 to O

4-2. MANUAL setting adjustment1 Set the WB switches to the MANUAL mode (both switches 7and 8 to OFF).

ADJUSTMENTS5. AGC1 Set the AGC switch (6) to ON.The on-screen setting for AGC will automatically switch toON. Press the CURSOR (j or l) button to sele

6. CAMERA ID1 Press the CURSOR (j or l) button to select NEXT PAGE(get it flashing), then press the SET button. The second pageof the “MENU FOR ADJUST

ADJUSTMENTS7. APERTURE1 Press the CURSOR (j or l) button to select NEXT PAGE(get it flashing), then press the SET button. The second pageof the “MENU

TROUBLESHOOTINGBefore taking the camera for repairs, please check below to make sure that the camera is usedcorrectly. If it still does not perform co

MENU FOR ADJUSTMENT CAMERA ID ON APERTURE WRITE PROTECT ON PREVIOUS PAGE ENDVBSVSL-LEIOFF ADJUSTMENT FOR AI (IRIS LEVEL) o------z-

Depending on the conditions of use,installation and environment, please be sureto make the appropriate settings andadjustments. If you need help with

ADJUSTMENT FOR VBS (PHASE) H o------z------p 280 SC o------z------p 90 ADJUSTMENT FOR VS (H SYNC PHASE) o------z------p 280 ADJUSTMEN

SPECIFICATIONSCamera:Scaning system : NTSC standard TV system (525 TV lines, 30 frames/sec.)Interlace : PLL 2:1 interlaceImage device : 1/3 inch solid

Safety GuardTHIS SYMBOL INDICATES THATTHERE ARE IMPORTANTOPERATING ANDMAINTENANCE INSTRUCTIONSIN THE LITERATUREACCOMPANYING THIS UNIT.WARNING:TO PREVE

PRECAUTIONSIn case of problemDo not use the camera if smoke or a strangeodour comes from the unit, or if it seems notto function correctly. Disconnect

PARTS NAMES1 Lens iris output connector (4 pin)This 4-pin connector is used to send the DC control signal andpower supply to an auto-iris type lens.2

PARTS NAMES9 Camera setup section (under the cover)This unit factory settings are as indicated below. These settingsare for when using a 1/3 inch CS m

F Video output connector (VIDEO OUT: BNC type)Connect this connector to a device such as a VCR or monitorwith a VIDEO IN connector.G External sync com

PARTS NAMES113LOCK2ADJ.Flange-back adjustmentIf the pick-up surface is not correctly positioned with relation tothe lens focal point, the picture will