Sanyo TLS-9072 User Manual download pdf (Page 34)

OUTPUT TERMINALS

TAPE END OUT Terminal

X During recording, when the end of the tape is reached

or when the tape counter reading indicates 1 hours 57

minutes or more, the output becomes 0V (Low).

X To reset the output, press the STOP or EJECT button.

X During autorepeat recording, when the end of the tape

is reached, the output becomes 0V (Low) for about 2

seconds only.

TAPE END OUT Terminal Output Setting

1 Press the MENU button until the (SET UP 3) menu is

displayed.

@@@@@@@<SET@UP@3>

*ALARM@MODE@@@@@@@Y1

*ALARM@DURATION@@@20S

*TAPE@IN@MODE@@@@@STOP

*TAPE@END@MODE@@@@REW

*TAPE@END@OUT@@@@@-3M

*CLOG@DETECT.@@@@@Y

2 Press the * (or +) button, until the “TAPE END OUT”

setting is flashing.

3 Press the l (or j) button, to select the desired

output mode.

–3M . . . . . . . The output becomes 0 V (Low)

when the tape counter reaches

“1

” and/or when the tape

reaches the end.

END . . . . . . . The output becomes 0 V (Low)

when the tape reaches the end.

4 Press the SEARCH/AUDIO ON button to save the

setting.

SW OUT Terminal

When recording, a pulse signal is output at the SW OUT

terminal.

This terminal is usually connected to the switch input (SW

IN) of devices like a camera switcher unit, or a quad

compressor.

SW OUT Terminal Output Setting

1 Press the MENU button until the (SET UP 4) menu is

displayed.

The FIELD (or FRAME) setting is flashing.

@@@@@@@<SET@UP@4>

*SW@OUT

@@FIELD@@@@@@@@@01

@@TIMING@@@@@@@@FIELD

@@2H@@@@@@@@@@@@Y

*THREAD@CHECK@@@Y

*VIDEO@LOSS@@@@@N

*REC@SPEED@@@@@@N

NOTE:

X If “TIMING” is set to FRAME (see step 4),

“FRAME” will be indicated instead of “FIELD”.

2 Press the l (or j) button to set the desired pulse

signal interval.

Available settings are:

FIELD. . . . . . 01, 02, 03, 04, 05, 10, 30 or 60 field

FRAME . . . . 01, 02, 03, 04, 05, 10, 30 or 60 frame

3 Press the * button, until the “TIMING” setting is

flashing.

4 Press the l (or j) button to set “FIELD” or “FRAME”.

FIELD. . . . . . 1 pulse is output after each set

number of fields.

FRAME . . . . 1 pulse is output after each set

number of frames.

5 Press the * button, until the “2H” setting is flashing.

6 Press the l (or j) button to set the desired “2H”

mode.

Y. . . . . . . . . . When recording in 2-hour mode, a

pulse signal is output.

N . . . . . . . . . When recording in 2-hour mode, a

pulse signal is not output.

7 Press the SEARCH/AUDIO ON button to save the

settings.

Tape end or 1

5V (H)

0V (L)

(Output impedance: 5.7 kΩ)

Output reset

5V (H)

0V (L)

(Output impedance: 5.7 kΩ)

FIELD

FRAME

: 16.7 msec.

: 5 msec.

RC4Q/NA2 (TLS-9072 GB) Thu. Sept., 07/2000

English 33

1 2 ... 29 30 31 32 33 34 35 36 37 38 39 40 41

Comments to this Manuals

No comments

Sanyo TLS-9072 User Manual Page 34

Comments to this Manuals

Related products and manuals for Cassette players Sanyo TLS-9072