Sanyo KHS0951 User Manual

INSTRUCTION MANUALSplit System Air ConditionerCOOL/DRY/HEAT ModelKHS0951KHS1251KHS1852Save These Instructions!Pub. OI-85264180351004 ©SANYO 2002 Print

Using the Remote Control UnitHow to Install BatteriesNOTE•The batteries last about six months, depending on how much you usethe remote control unit. R

11OI-351-11EGUsing the Remote Control Unit (continued)Mounting the RemoteControl UnitWhen attaching to wall 1) Confirm the indoor unit beeps when the

Operation with the RemoteControl Unit1. Automatic OperationNOTECheck that the circuit breaker on the power panel is turned on and that theoperation se

Operation with the Remote Control Unit (continued)Press TEMP. to change the temperature setting.•Although the fan speed is set automatically, you can

Operation with the Remote Control Unit (continued)2. Manual OperationNOTECheck that the circuit breaker on the power panel is turned on and that theop

Operation with the Remote Control Unit (continued)NOTE• This appliance has a built-in 3-minute time delay circuit to ensurereliable operation. When th

Operation with the Remote Control Unit (continued)4. Night Setback ModeThe Night Setback Mode is used for saving energy.Press the NIGHT SETBACK button

Operation with the Remote Control Unit (continued)17OI-351-17EGoi202000A. In Cooling and DRYMode:(and )When the night setback mode is selected, the ai

Special Remarks``DRY'' ( ) OperationHow it works?•Once the room temperature reaches the level that was set, the unitrepeats the cycle of tur

19OI-351-19EGSetting the Timer1. How to set thepresent time(Example) To set to 9:10 pm.Operation Indication1. Press the Program button ( )three times.

FeaturesThis air conditioner is equipped with cooling, heating and drying functions. Details on these functions areprovided below; refer to these desc

20OI-351-20EGSetting the Timer (continued)3. How to set the ON time(Example) To start operation at 7:10 am.Operation Indication1. Press the Program bu

21OI-351-21EGSetting the 1-Hour OFF Timer1. 1-Hour OFF TimerThis function causes the unit to operate for one hour and then stop, regardlessof whether

22OI-351-22EGAdjusting the Airflow Direction1. Horizontal The horizontal airflow can be adjusted by moving the vertical vanes with yourhands to the le

23OI-351-23EGOperation without the RemoteControl UnitIf you have lost the remote control unit or it has trouble, follow the steps below.1. When the ai

24OI-351-24EG1. With the ˝FRONT˝ mark facingyou, slide the anti-mold filterup into the unit and thenlower the handle into thegroove on the unit.2. Aft

25OI-351-25EGCare and Cleaning (continued)Air cleaning filter(not provided)The air cleaning filter removes dust and dirt from the air, and reduces odo

26OI-351-26EGCare and Cleaning (continued)Removing and remountingthe air intake grille•With the air intake grille open allthe way, grip both arms with

27OI-351-27EGTroubleshootingIf your air conditioner does not work properly, first check the following points before requesting service. If it stilldoe

oi330000oi202000SANYO FISHER COMPANYA DIVISION OF SANYO NORTH AMERICA CORPORATION21605 Plummer StreetChatsworth, CA 91311 U.S.A.In CanadaSANYO Canada

ContentsPageFeatures... 2Product Inform

Installation Location•We recommend that this air conditioner be installed properly byqualified installation technicians in accordance with the Install

Names of PartsNOTEThis illustration is based on the external appearance of a standard model.Consequently, the shape may differ from that of the air co

Unit Display and Operation SelectorRemote control receiver This section picks up infrared signals from the remote control unit(transmitter).Operation

24-hour clock with ON/OFF24-hour OFF Timer...1-hour OFF Timer...Remote Control Unit (Display)(1) Operation modeAUTO...

8OI-351-08EGRemote Control UnitSensorTransmitterDisplayNIGHT SETBACK button1 HR. TIMER buttonMODE selector buttonFLAP buttonADDRESS switch(Cover close

9OI-351-9EGRemote Control Unit (continued)Program button For details, see “Setting the Timer”.Press this button to select the mode you want to program