Sanyo SANUPS E11A102A User Manual download pdf (Page 26)

−

10. User Settings

10.1 Setup Menu Item List

You can configure the UPS by setting the menu items in the following list. Configure it according to your

environment and requirements.

The controls and indicators on the control panel are used to set items in the Setup menu. For details, see

§10.2 “Setup Menu Operations”.

Whenever you change a menu item setting, we recommend that you place a check mark in the “Current

Setting” field of the Setup Menu Item List.

●

LED blinks

○

LED off

No. Menu Item

Item Selection

LEDs

Setting

Item Setting

LEDs

Default

Setting

Current

Setting

Description Notes

Auto

●○○○

Switch the UPS operating mode automatically.

Double Conversion

○●○○

Set the UPS operating mode to Double Conversion mode.

①

UPS operation mode

●○○○○

Economy

●●○○

Set the UPS operating mode to Economy mode

100V

●○○○

100V setting (The default setting of Model: E11A102U001-00.)

110V

○●○○

110V setting (The default setting of Model: E11A102U001-10.)

115V

●●○○

115V setting (The default setting of Model: E11A102U001-15.)

②

Output voltage

(RESTART)

○●○○○

120V

○○●○

Refer

the

right

120V setting (The default setting of Model: E11A102U001-20.)

●○○○

±1% allowance

○●○○

±3% allowance

③

Frequency sync range

(RESTART)

●●○○○

●●○○

±5% allowance

Set the range (%) over which the output

frequency is adjusted to variations in the

input frequency in Economy Mode and

Active Filter Mode.

50Hz

●○○○

50Hz setting

④

Battery startup

frequency

○○●○○

60Hz

○●○○

60Hz setting

Set the inverter output frequency when

UPS restarts from the batteries from

stopped status.

Do not use this setting.

●○○○

－

Workstation

○●○○

Setting for communications by the power management software over serial

or LAN connection.

Serial Login

●●○○

Shutdown by serial login.

⑤

PC Interface mode

●○●○○

Do not use this setting.

○○●○

－

9600

●○○○

Set the baud rate to 9600 bps.

4800

○●○○

Set the baud rate to 4800 bps.

⑥

Serial baud rate

○●●○○

2400

●●○○

Set the baud rate to 2400 bps.

Set the communications baud rate when

a workstation, PC, or optional LAN card

is connected.

Auto

●○○○

Auto restart

OFF

○●○○

The UPS stays off.

30%

●●○○

Same behavior as Auto when

battery charge reaches 30%.

50%

○○●○

Same behavior as Auto when

battery charge reaches 50%.

⑦

Restart time

(battery charge rate)

●●●○○

80%

●○●○

Same behavior as Auto when

battery charge reaches 80%.

Specify when to restart the UPS after a

power outage and shutdown of the UPS

due to final discharge of the batteries.

When 30%, 50%, or 80% is selected, the

UPS does not restart until the batteries

are charged to the specified level.

All patterns

●○○○

All sounds

Pattern 1

○●○○

Do not emit sounds on power outage, battery test, battery test abnormal and overload.

Pattern 2

●●○○

Emit alarm and key click sounds.

⑧

Buzzer sound

○○○●○

OFF

○○●○

Emit key click sounds only.

1 second

●○○○

Turn inverter off when pressed for 1 second.

3 seconds

○●○○

Turn inverter off when pressed for 3 seconds.

Set the response time for

switch press to stop inverter

power supply.

⑨

switch

response time

●○○●○

Special operation

●●○○

Turn inverter off on special operation. Select this setting to keep the

inverter from being turned off by an accidental operation. See §9.4 "UPS

Shutdown (Daily)" for operation details.

Auto return

●○○○

Auto recovery with time

⑩

Overload recovery

operation

○●○●○

Bypass

○●○○

Fixed as bypass on overload

Set the conditions for automatic switch

back to inverter power supply (auto

return) after switching to bypass power

supply because of overload.

OFF

●○○○

The UPS stays off.

⑪

Inverter stop

Operation (RESTART)

●●○●○

Bypass

○●○○

Switch to bypass operation when

inverter stops.

Specify the UPS operation during

inverter power supply stops.

Battery voltage level

●○○○

When low battery voltage level is

detected.

2 minutes

○●○○

When remaining battery capacity

is 2 minutes.

⑫

Low battery voltage

signal timing

○○●●○

3 minutes

●●○○

When remaining battery capacity

is 3 minutes.

Specify the timing for triggering the low

battery voltage signal.

5 minutes

●○○○

5 minutes backup

15 minutes

○●○○

15 minutes backup

30 minutes

●●○○

30 minutes backup

60 minutes

○○●○

60 minutes backup

⑬

Battery backup time

●○●●○

180 minutes

●○●○

180 minutes backup

Set the UPS backup time on power outage.

An external battery must be connected for

settings of 15 minutes or higher.

(This item can’t take effect unless resetting

remaining battery life.)

5 years

●○○○

5 years lifetime type

10 years

○●○○

10 years lifetime type

⑭

Battery type

○●●●○

3 years

●●○○

3 years lifetime type

Set the battery type. Set this when you

exchange the battery or connect an external

battery. (This item can’t take effect unless

resetting remaining battery life.)

180 days

●○○○

Check batteries every 180 days.

90 days

○●○○

Check batteries every 90 days.

30 days

●●○○

Check batteries every 30 days.

⑮

Battery check schedule

●●●●○

None

○○●○

No battery check.

Set the interval (number of days) for the

automatic battery check. The check is

carried out automatically when the

specified number of days has elapsed.

Do not reset

●○○○

Do not reset.

－

⑯

Reset remaining

battery life

○○○○●

Reset

○●○○

Reset the battery information (remaining life, accumulated battery

operating time, number of power outages, LED remaining life display),

when you exchange the battery.

Note

Changes to some menu items do not take effect until you restart the UPS. These items are indicated by (RESTART) in

the "Menu Item" column. If a restart is required, be sure to power off the load devices before resetting. See §9.5 “UPS

Shutdown (If Not to Be Used for More Than a Week)” for information about how to shut down the UPS, and §9.1 “UPS

Startup (Normal Operation)” for information about how to start the UPS.

1 2 ... 21 22 23 24 25 26 27 28 29 30 31 ... 45 46

Comments to this Manuals

No comments

Sanyo SANUPS E11A102A User Manual Page 26

Comments to this Manuals