Sanyo DSR-3709 User Manual download pdf (Page 15)

INSTALLATION AND CONNECTIONS3

14 English

INTRODUCTION

The SENSOR ALARM OUT terminals are used to relay

alarm signals whenever one of the digital video recorder’s

motion sensors is triggered. Normally in an open condition,

a terminal adopts low condition when a sensor for the

corresponding camera number has been triggered.

The connections for a remote control circuit are shown

below. This digital video recorder can be remotely controlled

when a remote-control circuit similar to that shown here is

connected to the remote-input control terminals.

z Use a resistance of 1/10 ohms or more and with a D

ranking (Precision within ±0.5%).

z The remote control cable should be no more than 5 m

long.

* The DSR-3709 can operate up to nine cameras (*).

1 When you have finished making all the

other connections, make sure the

voltage is 120 V-240 V AC and insert the

power plug into the wall outlet.

There is no power switch. The display indicators flash, and after

a few moments, the monitor screen displays the camera image.

z When turning the power on for the first time

“PLEASE SET THE CLOCK” is displayed on the monitor

screen. Follow the procedures on P.17 to set the clock.

z If the clock is already set

The operation display area is displayed.

z If the POWER indicator starts flashing;

If a problem occurs during use, the POWER indicator

will begin to flash and an explanation will be displayed.

In these cases, contact a Sanyo service center.

z The power cord’s ground terminal is not provided for

enhanced safety; rather, it can be used to reduce the

level of interference when the digital video recorder is

connected to analog devices.

If a large amount of noise is generated when the digital

video recorder is connected to analog devices, connect

this terminal to the building’s earth.

Connecting SENSOR ALARM OUT

terminals

Connecting CONTROL terminals

Rating for each terminal

z Maximum current: 25 mA

z Maximum voltage: 25 V

R1C R2

SW 1

SW 2

SW 3

SW 4

SW 5

SW 6

SW 7

SW 8

SW 9

SW 10

SW 11

SW 12

SW 13

SW 14

SW 15

SW 16

SW 17

SW 18

SW 19

SW 20

SW 21

SW 22

SW 23

SW 24

SW 25

SW 26

SW 27

SW 28

SW 29

SW 30

SW 31

SW 32

R1 R2

: Camera 1*: INDEX +

: Camera 2*: INDEX -

: Camera 3*:

AUTO FOCUS

: Camera 4*: SEQUENCE

: Camera 5*: MON2

: Camera 6*: PLUS

: Camera 7*: QUAD

: Camera 8*: MULTI

: Camera 9*:

MENU RESET

: Camera 10:

: Camera 11: PAN left

: Camera 12: PAN right

: Camera 13: TILT down

: Camera 14: TILT up

: Camera 15: ZOOM wide

: Camera 16: ZOOM tele

: REC/STOP

: PLAY/STOP

: STILL

: SEARCH

SHIFT (Doubles with R1)

: PLAY

: REC

: MENU

: EXIT/OSD

: +

: -

→

←

: ZOOM

: COPY

: TIMER

(When combined

with R2 Shift key)

(When operated

independently)

Connecting the power cord

POWER

indicator status

Meaning

Four flashes per

second

There is a problem with the hard disk. The

hard disk must be replaced or initialized.

Contact a Sanyo service center to recover

recorded images.

One flash per

second

There is a problem with the fan.

120 V-240 V AC

(50/60 Hz)

01-01-04 00:00:00 REC REPEAT EN A ALARM 0000

Operation

display area

e00_l8h/jointfilesconvert/1261789/bg_us_7.book Page 14 Thursday, November 25, 2004 1:44 PM

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 125 126

Comments to this Manuals

No comments

Sanyo DSR-3709 User Manual Page 15

Comments to this Manuals

Related products and manuals for Video recorders Sanyo DSR-3709