Sanyo TLS-9024P User Manual download pdf (Page 19)

ALARM RECORDING

By connecting the ALARM IN terminal to a door switch,

an interphone, etc., a recording can be done only when

necessary.

Alarm Recording Setting

Alarm recording is performed when there is an input

(trigger) at the ALARM IN terminal, “AL” is displayed on

the digital display.

œ Make all necessary connections.

œ Follow the Before starting steps, under “NORMAL

RECORDING”.

1 Press the MENU button until the (SET UP 3) menu

is displayed.

@@@@@@@<SET@UP@3>

öALARM@MODE@@@@@@@Y1

öALARM@SPEED@@@@@@3H

öALARM@DURATION@@@20S

öTAPE@END@MODE@@@@REW

öTAPE@END@OUT@@@@@-3M

öCLOG@DETECT.@@@@@Y

öRS-232C@@@@@@@@@@19200

2 Turn the SHUTTLE ring to set the desired alarm

mode.

Y1 . . . . . . . . Alarm recording is done when there

is an alarm trigger.

Y2 . . . . . . . . Alarm recording is done only when

there is an alarm trigger during

programmed timer recording.

Y3 . . . . . . . . Alarm recording is done only if there

is an alarm trigger and the VCR is

not in programmed timer recording

mode.

Y4 . . . . . . . . Alarm recording is done only when

there is an alarm trigger during

programmed timer recording

duration. Timer recording is not

possible.

N . . . . . . . . . Alarm recording is not performed

even if there is an alarm trigger.

3 Turn the JOG dial, until the “ALARM SPEED”

setting is flashing.

4 Turn the SHUTTLE ring, to select the desired

recording speed.

3H . . . . . . . . 3-hour mode recording

12H . . . . . . . 12-hour mode recording

24H . . . . . . . 24-hour mode recording

NC. . . . . . . . Recording at the speed already set

5 Turn the JOG dial, until the “ALARM DURATION”

setting is flashing.

6 Turn the SHUTTLE ring, to select the desired alarm

recording duration (20S, 40S, 1M, 2M, 3M, 4M, 5M,

or CC).

20S-5M. . . . Recording only for the displayed

duration

CC . . . . . . . Recording as long as the alarm

signal is being input (minimum 5

seconds)

7 Press the SEARCH/AUDIO ON button to save the

settings.

NOTES:

œ During alarm recording all buttons are disabled.

œ If “OFF” is displayed on the digital display, alarm

recording is not possible in order to prevent the

recorded tape to be recorded over.

To cancel the “OFF” display, press the STOP,

EJECT or PLAY button or turn the SHUTTLE ring.

œ If an alarm trigger is received while alarm recording is

in progress, recording duration for the second alarm

will be calculated from that point. The alarm counter

will register the alarm, but it will not be found during

an alarm scan and alarm search.

œ If there is a power failure during alarm recording, and

the power is restored within the recording set

duration, alarm recording will continue.

œ If the alarm recording duration is short, the alarms

may not be found during an alarm scan or an alarm

search. If the alarms are going to be reviewed using

alarm scan or alarm search, then in 3-hour mode,

20-second or more recording duration should be

used.

œ To do alarm recording during series recording, set

“ALARM MODE” to “Y1” or “Y3”. Alarm recording will

be conducted only if the VCR is recording.

RR4Q/EX2 (TLS-9024P GB) Fri. Sept., 29/2000

18 English

1 2 ... 14 15 16 17 18 19 20 21 22 23 24 ... 38 39

Comments to this Manuals

No comments

Sanyo TLS-9024P User Manual Page 19

Comments to this Manuals

Related products and manuals for Video recorders Sanyo TLS-9024P