Sanyo HT27744 User Manual download pdf (Page 12)

➀

Mode Keys—Use these keys to program the remote control and to select the

operating mode (VCR, TV, CABLE, DVD, SAT, or AUX). To Operate Your...

VCR—Press the VCR key; Television—Press the TV key; Cable Box—Press the

CABLE key; DVD Player—Press the DVD key; and Satellite Receiver—Press the

SAT

key.

Note: Make sure you hold

down the mode key while entering a code number,

see page 13.

➁

Input Key—Press this key to change the input signal source as follows:

In the TV, DVD, Cable, and Satellite modes, this key selects the program source

to display on the screen (TV signal or signal from equipment connected to the AV

jacks). In the VCR mode, this key functions as a VCR’s TV/VCR key.

➂

Power Key—Press to turn TV on or off.

➃

Number Keys—Two keys must be pressed to select a direct channel. Example:

Press 0 then 6 to select channel 6. For Analog channels above 100, press and hold the

1 key until C1–– appears.

➄

Tuner Key—Use this key to toggle from one tuning system to another, digital

channels and analog channels.

➅

Channel (CH up / down) and Volume (VOL –/+) Keys—Press Up/down

keys to tune to the next higher or lower channel in the Channel Scan Memory

database. Press the –/+ keys to adjust volume. The screen displays a left or right

red arrow that blinks as many time as you press the Vol –/+ keys.

➆

Pix Shape Key—Use this key to change the video display format. Available

options depend on signal received and the broadcast aspect ratio: For HT27744/

HT32744—Letter box, Zoom, and Normal. For HT30744—Full, Zoom1/2, and

Normal. (See explanation of image shapes on page 5.) Note: If PAP feature is

selected, this key is not operable.

➇

Sleep Key—Press this key, then press the “0” key to set the Sleep Timer. The

desired time can be set from 30 minutes up to 3 hours in 30 minutes increments.

Sleep Timer will switch off the TV automatically.

Note: The Sleep Timer cancels when the TV is turned off or if a power failure

occurs.

➈

Recall Key—Select the first channel you want to watch; then select another

channel using the number keys. Press Recall to easily switch between the channels

without entering the channel numbers again.

Note: The Recall key can only toggle between channels within the same

signal source. Recall between a Digital channel and an Analog channel will

not work.

It takes only one remote to operate your TV and other equipment. Simply follow the

instructions on pages 13 ~ 15.

Point towards TV / Equipment

ANALOG

DIGITAL

VIDEO

COMPO

DMI

COMPO

PAUSEREC STOP

ON/OFF QUIK

VOL

MUTETUNER

INPUT RESET

PLAY

SWAP

PAP

PAP CHANNEL

FREEZE

AUDIO

SLEEP

PIX SHAPE

RECALL

CAPTION

INFO

654

123

DVD

VCR

CABLE

AUXSAT

POWER

654

123

GUIDE

PAGE

DOWN

ENTER

12 Remote Control

➇

➈

➉

➠

➅

➆

➀

➁

➃

➄

➂

Install Batteries as shown (2 AA, not included)

Notes:

Do not mix old batteries with new ones or mix different types of batteries together.

Remove the batteries if the remote control will not be used for a month or more.

Weak batteries may leak and cause damage. (Normal battery life is roughly six months.)

Using the Multimedia Remote Control

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 71 72

Comments to this Manuals

No comments

Sanyo HT27744 User Manual Page 12

Comments to this Manuals

Related products and manuals for TV Accessories Sanyo HT27744